GaN Talk Support Forum EPC

Topic	Replies	Views	Activity
GaNの話のサポート・フォーラムへようこそ！	2	614	July 19, 2022
What is the expected HBM (Human Body Model) ESD rating of the parts? Is there special handling required? GaN FETs and ICs Reliability and Quality	1	751	February 28, 2022
歡迎來到GaN Talk論壇!	2	607	July 19, 2022
Do you have an example for a 3-phase inverter? Motor Drive demo , industrial , medtech , motor-drive , automotive	1	739	February 28, 2022
Middle Power use SR GaN FET in ACF / LLC Demo Boards and Reference Designs	1	737	October 18, 2022
Does EPC have a development board for evaluation of eGaN devices in Class D Amplifiers? Demo Boards and Reference Designs development-board	1	736	February 28, 2022
Do I need to add insulation between eGaN FET and the heatsink? Characteristics of GaN FETs and ICs design , heatsink	1	733	February 14, 2022
How do GaN FETs fail at over current conditions GaN FETs and ICs Reliability and Quality design	1	731	August 25, 2022
Is a 2 kilowatt isolated DC-DC @ 48 volts unregulated full bridge configuration doable with GaN? DC-DC Conversion full-bridge , automotive , aerospace-defense , data-center , dc-dc	1	722	February 28, 2022
What is the best place to find general information on applying EPC’s enhancement mode GaN power devices?	1	720	February 28, 2022
How do we determine the power loop inductance? Assembly and Layout inductance	1	721	February 27, 2022
About EPC21601 information Lidar/Time of Flight (ToF)	1	719	August 24, 2022
Thermal management and heat sink options Designing with GaN FETs and ICs	1	713	March 7, 2023
Pin designation on GaN driver UP1966E Characteristics of GaN FETs and ICs	3	502	December 2, 2022
I plan to use four EPC2012C to make a full-bridge inverter for driving a wireless power transmitting coil. The input DC voltage is up to 120 V. Can you recommend a GaN-friendly half bridge driver for these conditions Wireless Power driver , full-bridge , consumer , medtech , wireless-power	1	708	February 28, 2022
What is the best method to remove heat from a 2 kilowatt isolated DC-DC @ 48 V unregulated full bridge? DC-DC Conversion temperature , thermal , data-center , dc-dc , consumer	1	708	February 27, 2022
In the LTSpice models, are the parasitic capacitances integrated directly into the model of EPC GaN FETs or do they have to be added? Designing with GaN FETs and ICs ltspice	1	700	February 28, 2022
Why are some GaN FET products suitable for ToF? Lidar/Time of Flight (ToF)	1	689	December 31, 2023
Per your data sheet, I note that your eGaN FETs TJ should be <150°C; what is TJ for the specified test condition? industrial , data-center , consumer , medtech , communications	1	688	June 16, 2022
Use Half bridge DC2DC Buck with EPC90150 DC-DC Conversion	1	687	June 5, 2024
Can eGaN FETs be paralleled? If so what are the key elements for a good design? design	1	687	February 28, 2022
EPC9192KIT power configurations	2	559	June 26, 2024
Using isolated supplies instead of bootstrap Designing with GaN FETs and ICs	1	684	November 16, 2023
用于dc/dc应用的氮化镓器件	1	678	May 11, 2022
Why is the hard switching gate loop more critical than the GaN acting as a diode and risking induced turn on? Assembly and Layout diodes	1	677	February 27, 2022
Dead time requirements in a motor drive Designing with GaN FETs and ICs motor-drive	1	676	February 9, 2023
LED Driver LT3763 with GaN Fets Designing with GaN FETs and ICs	3	477	September 13, 2024
Are GaN FETs prone to small area overheating? Characteristics of GaN FETs and ICs temperature	1	673	February 27, 2022
What method do you recommend to measure the case temperature of EPC devices? Designing with GaN FETs and ICs temperature	1	673	February 28, 2022
What is the best way to remove a GAN FET off a PCB without damaging the FET? Assembly and Layout pcb	1	670	February 27, 2022
Wafer level chip scale assembly considerations Assembly and Layout	1	664	March 16, 2023
How do you measure the VGS and the VDS when you use a very compact layout? Assembly and Layout layout	1	663	February 27, 2022
Subnano Pulse Driver Application Assembly and Layout	1	656	January 2, 2024
Recommended Assemblers Designing with GaN FETs and ICs	2	535	October 5, 2022
What are the limitations on the gate input for EPC’s eGaN devices? Characteristics of GaN FETs and ICs	1	656	February 14, 2022
Can EPC2036 be used in half bridge circuit?	3	463	December 4, 2023
GaN Fets in 3-phase PMAC motor inverter - Bus Pump issue Designing with GaN FETs and ICs	4	417	January 13, 2025
EPC2302 Paralleled GaN Devices	1	654	December 12, 2023
How do I predict failure rates for the EPC eGaN FETs? GaN FETs and ICs Reliability and Quality	1	653	February 28, 2022
Does EPC have plans to produce GaN diodes? diodes	1	653	February 13, 2022
I need to know the load range impedance requirements to obtain a good result on the EPC9065 development board Demo Boards and Reference Designs	1	645	February 28, 2022
GaN Power Devices and Applications	2	524	August 23, 2022
I notice you put VIAs under CAP Pads. Is there any solder liability impact? Assembly and Layout solder , vias	1	641	February 27, 2022
Efficiency trade offs and available models Designing with GaN FETs and ICs	1	640	February 10, 2023
The high frequency capability of the devices could be an issue with the layout of my circuit board. What must I be mindful of when laying out my circuit? pcb	1	639	February 28, 2022
Your threshold voltage is low compared with silicon MOSFETs. How does this impact turn off speed? silicon	1	641	February 28, 2022
Do the logic signals have to be isolated from the IC on the EPC2152 ePower™ Stage's HS and LS pins? Motor Drive dc-dc , industrial , motor-drive	1	633	February 28, 2022
What considerations need to be made in regard to stencil design? Assembly and Layout design	1	633	February 27, 2022
SOA data clarification Designing with GaN FETs and ICs design , dc-dc	1	633	February 9, 2023
Does EPC have application information on the use of eGaN FETs in micro inverter applications for solar panels? DC-DC Conversion solar , micro-inverter , dc-dc , ac-dc	1	632	February 28, 2022